Overhead Door Model 55b Remote

1. Overhead Door Model 55b Remote Controls
2. Overhead Door Model 55b Remotes
3. Overhead Door Model 55b Remote Control

OVERHEAD DOOR REMOTE. OVERHEAD DOOR BRAND REMOTES. 390MHz (1) 360MHz (1) 340MHZ (1) ALSO AVAILABLE IN A KEY CHAIN SIZE. This is a very robust product that has very good range. A quality item made by Keystone / Heddlof. 9 DIP SWITCH PROGRAMING (0 + –) VERY EASY TO PROGRAM TO YOUR OVERHEAD DOOR BRAND. Chamberlain Group (CGI), the corporate parent company to LiftMaster, Chamberlain, Merlin and Grifco, is a global leader in access solutions and products. We design and engineer residential garage door openers, commercial door operators and gate entry systems.

All garage door remotes operate in one of two ways shown below.

My mother's very old house, circa 1978, has a functioning Overhead Door garage door opener (model 100, NOT 100a) but her remote finally died. I ordered a replacement which tells how to program it for the digital code models. Founded in 1921, the Overhead Door Corporation has since become one of the most well-known manufacturers of residential and commercial garage doors and openers in the United States. The Phantom 777CD is an ultra-quiet, belt-drive residential garage door opening system.

Shop for remotes by the number of dip switches or by rolling code, then by frequency.

Programming your Overhead Door Codedodger® wireless keypad. Should you need additional information please contact our customer service department at 1-800-275-6187.

Resetting your keypad:

If, at any time, during programming, you should enter the wrong PIN or make a mistake, you should reset the keypad to its factory setting.

1. Open the keypad cover half way

2. Press and hold the number 8 and the PROG buttons while opening cover fully.

3. The indicator light will blink once and go out.

4. Close the cover. You are now ready to re-program your keypad.

Basic Programming:

1. Open cover fully - Indicator will blink once on go out

2. Press 3-5-7

3. Press PROG - Indicator will blink once per second

4. Enter PIN 1 (up to 8 digits)

5. Press PROG - Indicator will blink twice per second

6. Close cover. Your keypad is now ready to be programmed to the garage door opener.

   Looking for online definition of MAC or what MAC stands for? MAC is listed in the World's largest and most authoritative dictionary database of abbreviations and acronyms. (slang for Apple computer) MAC: Mandatory Access Control: MAC: Medium Access Control: MAC: Mid-American Conference. Marine Aquarium Council: MAC: MacPaint (File Name. There are three common technology definitions for MAC: (1) Short for Media Access Control. See MAC address or MAC layer. (2) When spelled Mac, the brand name and registered trademark for a line of computers from Apple Inc. See under Macintosh computer. (3) Short for Mandatory Access Control. Turn off the computer and make sure all cords are disconnected. You don't want to get accidentally.

   Locate the Learn code button on your Codedodger garage door opener.

   Depending on model, the learn code button will be located under the light cover or on the rear panel.

Basic Opener Programming:

1. Press the learn code button - Learn code LED will flash

2. Open cover on keypad fully

3. Enter PIN number

4. Press the SEND button 4 times, or until the door begins to operate.

5. You will now be able to use your wireless keypad normally.

Controlling a single door with your keypad:

1. Open keypad fully

2. Press PIN number

3. Press SEND once

4. Door should operate normally

   Note: As a 'panic' feature this keypad will operate door for up to 30 seconds from any button.

Programming multiple doors with your keypad:

Program your keypad according to the steps outlined in the Basic programming section listed above.

1. Open cover fully

2. Enter PIN number

3. Press PROG - Indicator will blink once per second

4. Press PROG - Indicator will blink twice per second

5. Press PROG - Indicator will blink three times per second

6. Enter the total number of doors (2 or 3) Word for mac import style into existing document.

7. Press PROG

8. Close cover

9. Your keypad is now ready to be program to the garage door openers.

10. Locate the learn code button on your garage door openers

11. Press the learn code button once - Learn code indicator will flash

12. Open cover on keypad fully

13. Enter PIN

14. Press SEND

15. Enter door number 1-2-or-3

16. Press send button 4 times, or until door operates

17. Repeat these steps for door 2 and 3

Controlling multiple doors:

1. Open cover fully

2. Enter PIN number

3. Press SEND

4. Enter door number (1-2-or 3)

5. Chosen door should operate

Adding PIN 2:

Overhead Door Model 55b Remote Controls

1. Open cover fully

2. Enter 1-5-9

3. Press PROG - Indicator will blink once per second

4. Enter PIN 2 (up to 8 digits)

5. Press PROG Indicator will go out

6. Close cover. Your keypad is now ready to be programmed to the garage door opener.

7. See steps in Basic programming.

Adding temporary PIN:

1. Open cover fully

2. Enter PIN 1

3. Press PROG - Indicator will blink once per second

4. Press PROG - Indicator will blink twice per second

5. Enter temporary PIN

6. Press PROG - Indicator will blink three times per second

7. Close cover. Your keypad is now ready to be programmed to the garage door opener.

8. See steps in Basic programming.

Canceling the temporary PIN:

The temporary PIN will remain active until PIN 1 is entered.

Overhead Door Model 55b Remotes

Changing a PIN:

Overhead Door Model 55b Remote Control

1. Open cover fully

2. Enter PIN to be changed

3. Press PROG Indicator will blink once per second

4. Enter new PIN

5. Press PROG

6. Indicator will blink twice if PIN 1 has changed or go out if PIN 2 was changed

7. Close cover. Your keypad is now ready to be programmed to the garage door opener.

   Locate the Learn code button on your Codedodger garage door opener.

   Depending on model, the learn code button will be located under the light cover or on the rear panel.